- CENTURY 1081 POOL PUMP DUTY MOTOR PART MANUAL
- CENTURY 1081 POOL PUMP DUTY MOTOR PART PRO
- CENTURY 1081 POOL PUMP DUTY MOTOR PART PLUS
PLUS The - NEW - Triple Seal protection feature is designed into the pump end of the motor to protect the bearings from water, pests and debris, extending the life of the motor.
CENTURY 1081 POOL PUMP DUTY MOTOR PART PRO
The Centurion Pro motors are highly durable and easy to install, no other replacement pump motor comes close to a superbly crafted Century Centurion® PRO pool and spa motor. Why choose the Century Centurion PRO Motors over any other pool pump motors? What are the benefits? Most durable and economical solution in the market today.Premium sealed 203 bearings at both ends.Designed for optimal performance and efficiency.Long lasting ( When properly Installed and Protected from Mother Nature ).Fast and easy installation with the open and accessible terminal board and wiring compartment.Triple Seal Protection on pump-end bearing protects the bearing from water, pests and debris, extending the life of the motor.Standard Features of Century Electric HST110 Centurion PRO Pool Pump Motors Watts Quick-Change (QC) Replacement FiltersĬentury Electric HST110 Pool Pump Motor is the Pool Industry's Leading replacement motor for AO Smith ST1072, AO Smith UST1102, Emerson EST1072, Emerson EUST1102, US Motors ( Nidec ) AST125, Hayward SPX1607Z1M, SN Tech C109, SN Tech C1318, Bluffton B1318, AO Smith B228SE, Marathon C1318, Marathon 5KC39PN2822X.Watt Quick Change (QC) Replacement Filters.Watts Quick-Twist (QT) Replacement Filters.OneFlow (Residential) Anti-Scale Systems.OneFlow (Commercial) Anti-Scale Systems.Submersible Replacement Motors ( ONLY ).Don't see your pump listed? See our complete list of pump seals here: Pump Seal Cross Reference. It is recommended to replace the shaft seal along with a pool pump motor replacement. The mechanical shaft seal prevents leaking along the motor shaft. Fill pump strainer with water, lubricate pump lid o-ring and tighten lid securely Lubricate seal plate o-ring, and tighten seal plate clamp band or bolts securelyġ2.
Replace motor end cap and test motor power briefly for 1-2 seconds, before sliding motor back into the pump housingġ1. Spin impeller CCW onto threaded motor shaft until snug, replace wear ring and diffuser over the impellerġ0. Replace motor seal plate onto new motor, installing new shaft seal in the same orientation as on the old motorĩ. Remove conduit elbow from old motor and thread onto new, run power wires thru elbow and connect to new motorĨ. Remove seal plate from the old motor by removing the locknuts, and tapping or prying gently if neededħ. If there is an impeller screw, these are reverse threadĦ. Loosen the Impeller by hand or use large pliers to remove. Loosen capacitor bracket to move it out of the way, and place a 1/2" wrench on the slotted end of the motor shaftĥ.
Remove motor end cap and disconnect ground wire and two power leads, and gently pull wires out of motorĤ. Remove the clamp band or the bolts to separate motor from pump pull motor out of pump housingģ. 56Y frame has a ½” larger barrel diameter than the slimmer 48Y, which includes a rubber spacer to adapt.Ģ. Both frame types have identical bolt hole spacing, face and shaft.
CENTURY 1081 POOL PUMP DUTY MOTOR PART MANUAL
Fits Pentair Challenger, MaxeGlas II, DuraGlas II, SuperFlo, SuperMax, WhisperFlo.ĥ6Y is interchangeable with 48Y. NEPTUNE Programmable Pool Pump Motor/Control Installation and Operation Manual Models: 1.65 THP, 2.25 THP, and 2. Fits Anthony, Hayward Max-Flo II, StaRite MaxeGlas, DuraGlas, DynaGlas, Pentair UltraFlo.ĥ6C Keyed Shaft: Round C-Flange motors with slotted shaft to fit old-style bronze pumps by American Products, Anthony, Baker-Hydro, Purex and Sta-Rite/Swimquip.ĥ6J C-Flange: Round C-Flange motors with threaded shaft used on Hayward inground pumps, fits MaxFlo, Superpump and Super II, Jacuzzi Magnum and Jandy HP.ĥ6Y Square Flange: 4-holes on a square frame, bolts to pump housing. Fits Astra, Dynamo, Executive, Hi-Flo, JWPA, Pinnacle, PowerFlo, OptiFlo.Ĥ8Y Square Flange: 4-holes on a square frame, bolts to pump housing. When replacing a pool motor, replace with the correct frame type, horsepower and whether it is up-rated or full-rated motor, and replace the shaft seal when installing a new motor.Ĥ8 Frame: Thru-bolt motors with built-in pedestal used on spas and above ground pools. The industry average is about 8 years for pump motors. When a pool motor beings to squeak and squeal, overheat, hum or just won't turn on - it may be near the end of useful life. In The Swim Knowledge Pool Pool Pump Motor Replacements